【資料名稱】：新設備CP60,APG43調(diào)測流程

【資料作者】：ERI

【資料日期】：2009-03-01

【資料語言】：中文

【資料格式】：DOC

【資料目錄和簡介】：

100_1532-B_AXE10699（APG43 STARTUP）
101_1532-B_AXE10699（CP60 STARTUP）
102_1532-B_AXE10699（APG43 STARTUP）
103_1532-B_AXE10699（CP60 NETEST）

Factory Start Up and Initial NE Test of APG43--123頁，2008.12.08
1 Introduction 4
1.1 Concerned Hardware 4
2 Range of Test 5
2.1 Work Flow 5
2.2 Typographic Convention 6
3 Conditions before Starting 6
3.1 General 6
3.2 Supported APZ Source Systems 7
4 Test Tools 7
5 General 8
5.1 Schematic Overview – APG43 9
5.2 APG43 Board Positions 11
5.2.1 BSC Board Configuration with APZ 212 55 11
5.2.2 CN Board Configuration with APZ 212 55 12
5.2.3 CN Board Configuration with APZ 212 60 13
5.3 Board Information of eGEM with APG43 and APZ 212 55/60 14
5.4 APG43 Architecture 16
5.5 APG43 Cabling for Magazine with APZ 212 55 or APZ 212 60 17
6 Method 19
6.1 Preparation 19
6.1.1 Board Positions 19
6.1.2 Cabling 19
6.1.3 Check the Strap Connectors 19
6.1.4 Power Up 19
6.1.5 Connect to the APG43 19
6.2 Check Resources and Installed Clone Image 20
6.2.1 Checking State of Cluster Resources 20
6.2.2 Checking GPO 22
6.2.3 Checking Replication 23
6.2.4 Modify Registry Setting 25
6.2.5 Checking Installed Clone Image 26
6.3 APG43 Backup Verification 27
6.4 Definition of HWC 29
6.4.1 Definition of the Boards 29
6.4.2 Check Master/Slave relationship 35
6.5 Configuration of SMO 37
6.6 Prepare for Site Parameter Change 40
6.6.1 Name Rules and Recommendation 41
6.6.2 Check Current Site Parameters 42
6.6.3 Check the RAID 47
6.7 Parameter Change 54
6.7.1 General 54
6.7.2 Pre CloConfig Steps 54
6.7.3 CloConfig Steps 55
6.7.4 Post CloConfig Steps 57
6.8 Configure APG43 for APZ 61
6.8.1 STS Setting 61
6.8.2 TFTP Setting 62
6.8.3 MAS Setting 63
6.8.4 ACS Setting 64
6.9 Administrator and Guest Account 65
6.10 Anti-Virus SW Configuration 66
6.10.1 Automatically Antivirus Update 66
6.10.2 Manual Antivirus Update 68
6.10.3 Directly towards a Local Distribution Server inside the Factory 71
6.11 Connection with APG43 72
6.12 Configuration for Two APG43s 73
6.13 Audit Script 75
7 Helpful Hints (Appendix) 76
7.1 Communication Interface 76
7.2 Using Remote Desktop 78
7.3 Increased Security 78
7.4 Backup and Restore of APG43 SW 78
7.4.1 Backup of APG43 SW and Transfer to DVD 78
7.4.2 Restore APG43 SW from DVD 82
7.5 CP Configuration 85
7.5.1 Define Exchange Volumes on AP1 85
7.5.2 Transfer PES and CPHW Dumps to AP1 86
7.5.3 Configure Microsoft Internet Information Server 91
7.5.4 Transfer of CP-Dump to AP1 93
7.5.5 Set STSCBIN Parameter 95
7.5.6 Set APCONF Parameter 100
7.5.7 Post CloConfig Steps 104
7.6 Console Connections 105
7.6.1 Fetching Public IP address via Console 105
7.6.2 Changing IP addresses via Console 107
7.7 AP Commands 110
7.8 IP Addresses of the APG43 113
7.9 MODDBIN or CSBIN 113
7.10 STRABs 114
7.11 References 115
8 Revision Information 118
9 Glossary 120
9.1 Terminology 120
9.2 Abbreviations 121
Factory Start Up and Initial NE Test of APZ 212 55 and APZ 212 60--90頁，2008.11.27
1 Introduction 4
1.1 Concerned Hardware 4
2 Range of Test 4
2.1 Work Flow 5
3 Conditions before Starting 5
4 Test Tools 6
5 General 6
5.1 APZ 212 55 Front Side 6
5.1.1 BSC Board Configuration 7
5.1.2 CN Board Configuration 8
5.2 APZ 212 60 Front Side 9
5.2.1 CN Board Configuration 9
5.3 Board Information of eGEM with APG43 and APZ 212 55/60 10
5.4 Cabling for APZ 212 55 and APZ 212 60 11
6 Method 12
6.1 Preparation 12
6.1.1 Board Positions 12
6.1.2 Cabling 12
6.1.3 Check the Strap Connectors 12
6.1.4 Power Up 12
6.1.5 Connect to the APG43 12
6.2 Board Definition of APZ 212 55 in eGEM 13
6.2.1 Definition 13
6.2.2 Setting CP Identification Values 17
6.2.3 Check Master/Slave relationship 18
6.2.4 Definition of RPBI-S 20
6.3 Board Definition of APZ 212 60 in eGEM 22
6.3.1 Definition 22
6.3.2 Check Master/Slave relationship 25
6.4 Check that IPMI Master is Set for one SCP-RP4 27
6.5 Transfer PES and CPHW Dumps to APG43 28
6.5.1 Installation in a One CP system 28
6.5.2 Installation on a Multiple CP system 30
6.6 Activate the new PES and CPHW dump 31
6.6.1 Activation on a One CP system 31
6.6.2 Activation on a Multiple CP system 32
6.7 Transfer of CP Dump to APG43 33
6.8 Test of Connection between APG43 and APZ 212 55/60 36
6.9 Check DHCP Settings 42
6.10 Configuration of Microsoft IIS 45
6.11 Boot Start CPU 49
6.12 Initial Test 53
6.13 Initial Loading of CP-A 56
6.14 Initial Loading of CP-B 61
6.15 GESB with ESS Functionality 67
7 HELPFUL HINTS 68
7.1 Exchange Data 68
7.1.1 Printouts to Command hwcls 68
7.1.2 Useful CPT Commands 68
7.1.3 Checking Middleware PES and CPHW Information 69
7.2 Manual Rotation of RELFSW Files 73
7.3 Information Displayed by a CDU 75
7.3.1 Left-Most Digit, Encoding 75
7.3.2 Numerical Value, Intervals 75
7.3.3 Numerical Values, during Loading of CP 76
7.3.4 Numerical Values, during remote Upgrade of Firmware 77
7.3.5 Numerical Values, when a Fault is detected during CP Loading 78
7.3.6 Description of Indicators 81
7.4 MODDBIN or CSBIN 82
7.5 STRAP Connectors 83
7.6 References 83
8 Revision Information 86
9 Glossary 87
9.1 Terminology 87
9.2 Abbreviations 88
Factory NE Test of APG43--51頁，2008.12.08
1 Introduction 3
1.1 Concerned Hardware 3
2 Range of Test 4
2.1 Work Flow 4
2.2 Typographic Convention 5
3 Conditions before Starting 5
3.1 General 5
3.2 Supported APZ Source Systems 6
4 Test Tools 6
5 General 7
5.1 Schematic Overview – APG43 8
5.2 APG43 Front Side 9
5.2.1 BSC Board Configuration with APZ 212 55 10
5.2.2 CN Board Configuration with APZ 212 55 11
5.2.3 CN Board Configuration with APZ 212 60 12
5.3 Board Information of eGEM with APG43 and APZ 212 55/60 13
5.4 APG43 Architecture 15
5.5 APG43 Cabling 16
6 Method 18
6.1 Preparation 18
6.1.1 Cabling 18
6.1.2 Alarm Connections 18
6.1.3 Power Up 18
6.1.4 Connect to the APG43 18
6.2 Check of Data 19
6.3 Test of APG43 20
6.3.1 Test when only APM SW is Installed and Active 21
6.3.2 Test when also APIO SW and STS SW are Installed and Active 21
6.4 Start Up and Test of External Alarm System 25
6.5 Test of Alarm Panel and Circuits 28
6.6 FAN Test for BFD 509 08/3 30
6.7 Test of IO Device 31
6.8 Configuration Change for the SSU Folder 32
6.9 Backup of APG43 SW and Transfer to DVD 33
6.10 SFTP Verification 37
6.11 Restore of APG43 SW from DVD 38
6.12 Audit Script 41
7 Helpful Hints 42
7.1 Using Remote Desktop 42
7.2 Exchange Data 42
7.2.1 Spontaneous Printouts 42
7.2.2 Routing of Alarm Printouts 43
7.2.3 Configuration of Alarm Printer 44
7.2.4 Heartbeat Configuration in APIO 44
7.2.5 External Alarm 44
7.2.6 Port Definition 44
7.3 References 45
8 Revision Information 48
9 Glossary 49
9.1 Terminology 49
9.2 Abbreviations 50
Factory NE Test of APZ 212 55 and APZ 212 60--63頁，2008.11.13
1 Introduction 4
1.1 Concerned Hardware 4
2 Range of Test 4
2.1 Work Flow 6
3 Conditions before Starting 7
4 Test Tools 7
5 General 7
5.1 APZ 212 55 Front Side 7
5.1.1 BSC Board Configuration 8
5.1.2 CN Board Configuration 9
5.2 APZ 212 60 Front Side 10
5.2.1 CN Board Configuration 10
5.3 Board Information of eGEM with APG43 and APZ 212 55/60 11
5.4 Cabling for APZ 212 55 and APZ 212 60 13
6 Method 14
6.1 Preparation 14
6.1.1 Requirements 14
6.1.2 Power Up 14
6.1.3 Connect to the APG43 14
6.2 Activate Weekly Routine Test 14
6.3 Manual Intervention when CP-A is EX 16
6.4 Manual Intervention when CP-B is EX 19
6.5 Manual Initiated Small Restart 21
6.6 Manual Initiated Large Restart 22
6.7 Activate the Command Log 24
6.8 Manual Initiated Large Restart with Reload from MS 27
6.9 Manual Initiated Large Restart with Reload from File 31
6.10 FEX Load by Disconnecting CPU-Boards 34
6.10.1 FEX Load on CP-A 34
6.10.2 FEX Load on CP-B 37
6.11 Function Change Method II 39
6.12 Clear All SYRIP Information 42
7 HELPFUL HINTS 45
7.1 Exchange Data 45
7.1.1 Adjunct Processor File 45
7.2 Command Log 45
7.2.1 Command Log, Activate 45
7.2.2 Command Log, Deactivate 46
7.3 AP Audit Log 46
7.3.1 Activation of AP Audit Log 46
7.3.2 Deactivation of AP Audit Log 47
7.4 Manual Rotation of RELFSW Files 48
7.5 Exchange Header Information at FEX loading 50
7.6 Information Displayed by a CDU 50
7.6.1 Left-Most Digit, Encoding 50
7.6.2 Numerical Value, Intervals 51
7.6.3 Numerical Values, during Loading of CP 51
7.6.4 Numerical Values, during Remote Upgrade of Firmware 52
7.6.5 Numerical Values, when a Fault is detected during Loading of CP 53
7.6.6 Description of Lamps 56
7.7 References 57
8 Revision Information 59
9 Glossary 60
9.1 Terminology 60
9.2 Abbreviations 61



新設備的到來,希望對大家有用

[ 本帖最后由 laomaoyixin 于 2009-5-11 23:07 編輯 ]