【資料名稱】：愛立信參數說明詳解

【資料作者】：未知

【資料日期】：未知

【資料語言】：中文

【資料格式】：DOC

【資料目錄和簡介】：

愛立信ObjType和參數解釋?zhuān)?br /> CELL LOCATING DATAAW允許指配到較差小區Assignment to worse cell switch.This parameter identifies if assignment to worse cell is allowed.
CELL LOCATING DATASCHO允許SDCCH切換SDCCH handover switch.This parameter identifies if handover on Stand Alone Dedicated Control Channel (SDCCH) is allowed.
CELL LOCATING DATAMISSNM允許連續丟失的最大測量報告次數Maximum number of consecutive missing measurements.This parameter indicates the maximum number of consecutive missing measurements, for serving or a neighbouring cell, permitted before all old measurements are considered invalid.
CELL LOCATING DATABSPWRBCCH控制信道的有效發射功率Base station effective radiated power.This parameter indicates the base station Effective Radiated Power (ERP) in dBm, for the absolute Radio Frequency (RF) channel in the cell defined for Broadcast Control Channel (BCCH).
CELL LOCATING DATABSTXPWR話務信道的有效發射功率Base station effective radiated power.This parameter indicates the Base Station ERP in dBm, for the absolute RF channels in the cell or subcell not defined for BCCH.
CELL LOCATING DATAMSRXMIN手機測到最小信號強度，即下行最小信號強度門限，信號高于此值的小區進行切換考慮Lower limit of signal strength in MS.This parameter indicates the lower limit of signal strength in negative dBm, in Mobile Station (MS).Numeral 0 - 150.
CELL LOCATING DATABSRXMIN基站測到最小信號強度，即上行最小信號強度門限，信號高于此值的小區進行切換考慮Lower limit of signal strength.This parameter indicates the lower limit of signal strength in negative dBm, in Base Station (BS).Numeral 0 - 150
CELL LOCATING DATAMSRXSUFF下行足夠電平闕值Sufficient signal strength in MS。This parameter indicates the sufficient signal strength in negative dBm for path loss criteria in MS.Numeral 0 - 150
CELL LOCATING DATABSRXSUFF上行足夠電平闕值Sufficient signal strength。This parameter indicates the sufficient signal strength in negative dBm, for path loss criteria in BS.Numeral 0 - 150
CELL LOCATING DATAEXTPEN支持切換懲罰，用于表示MSC和目標BSC是否支持切換懲罰Handover penalty support . This parameter identifies if the Mobile Services Switching Centre (MSC) and target Base Station Controller(BSC) support penalty handling.Default value: OFF . ON enalty handling supported . OFF enalty handling not supported
CELL LOCATING DATAHYSTSEP信號強度離析器，用于指示高信號和低信號小區Signal strength separator.This parameter indicates the signal strength separator for high and low signal strength cells in negative dBm.
CELL LOCATING DATAISHOLEV內部切換水平系統，當空閑話務低于該值時，啟動切換評價系統Inter system handover level.Inter system handover evaluations start when the percentage of idle fullrate Traffic Channels (TCHs) left in the cell is less than or equal to this value given as percentage.The availability of this parameter value depends on commercial agreement relating to optional feature "GSM - UMTS Cell Reselection and Handover".
CELL LOCATING DATAFBOFFSP正的頻帶群偏移量，用于設置高頻段和低頻段的區別Positive frequency band group offset.This parameter sets the difference in pathloss between the lower frequency band group and the higher frequency band group.The availability of this parameter value depends on commercial agreement relating to optional feature "Multi Band Cell".
CELL LOCATING DATAFBOFFSN負的頻帶群偏移量，用于設置高頻段和低頻段的區別Negative frequency band group offset.This parameter sets the difference in pathloss between the lower frequency band group and the higher frequency band group.The availability of this parameter value depends on commercial agreement relating to optional feature "Multi Band Cell".