【資料名稱】：臺州諾西參數

【資料作者】：移動

【資料日期】：2010

【資料語言】：中文

【資料格式】：DOC

【資料目錄和簡介】：

The parameter indicates whether handover margins for signal level and quality will be taken into account in the handover decision algorithm.is set no the ho due to lev and qual is refuse.enableHoMarginLevQual(Y/N)
The parameter is used as a threshold in a handover caused by signal level.hoMarginLev(-24…24)db
The parameter is used as a threshold in a handover caused by signal quality.hoMarginQual(-24…24)db
The parameter is used in order to prevent repetitive handover between adjacent cells. It may be also used as a threshold in the power budget processhoMarginPBGT(-24…63)db
The parameter contains the minimum signal level measured by the MS when a handover is allowed to an adjacent umbrella cell. The signal level can be set independently for each adjacent cellhoLevelUmbrella(-110…-47)dbm
OPTIONAL (Fast moving MS handling in macro cell)The parameter defines the limit which is compared with the identification counter in the adjacent cell.unit is sacch frames,if the nb's receive lev is above rxlevmincell,a counter is increased by 2,otherwise decreased by 1.if counter exceed the FMT,UMbrelle ho triggered (only when nbrelev>AUCL),if FMT=0,not in use compare ,if AUCL is ok,get into umbrella,if FMT=255,then mean let the counter always increase not triggered the HOthreshold.fastMovingThreshold(0…255) sacch frame
OPTIONAL (Chained cells in rapid field drop)The parameter defines the adjacent cell as a chained cell to which the rapid field drop handover criteria is appliedchainedAdjacentCell(Y/N)
OPTIONAL (Intelligent Directed Retry (IDR))Type of cell.Check adjacent cell parameterscellType(GSM/MCN/shared)
"OPTIONAL (Improved solution for extended range cell)
You can check the values of the HOTargetArea parameter with the EAT command.
The parameter indicates whether the adjacent cell is a normal cell or an extended cell.
The meanings of the HOTA values are:
0 Normal cell or DE21/DF12 BTS (Nokia 2nd
generation) extended cell.
1 BTS DE34/DF34 (Nokia Talk-family)
extended cell, BSC tries to allocate a new
channel from a normal transceiver (N-TRX).
2 BTS DE34/DF34 (Nokia Talk-family)
extended cell, BSC tries to allocate a new
channel from an extended transceiver
(E-TRX).
3 BTS DE34/DF34 (Nokia Talk-family)
extended cell, BSC tries to allocate a new
channel from a transceiver that is of the same
type than the transceiver where the call exists
"hoTargetArea
Maximum transmit power of the MS for an adjacent cell.The parameter must be the same as ms txpwr max of an adjacent cell.(S3 feature)msTxPwrMaxCell(5…43 step 2)*GSM* dbm
Maximum transmit power of the MS for an adjacent cell.The parameter must be the same as ms txpwr max of an adjacent cell.(S3 feature)msTxPwrMaxCell(0…36step 2)*DCS* dbm
"OPTIONAL (Optimization of the MS Power Level in Handovers)The parameter indicates whether the RF power level that is used by the MS on a channel of the new cell after a handover is optimized to correspond with the radio link properties of the new cell. If optimization is enabled, the parameter indicates also the desirable uplink signal level after the handover.
The optimization procedure works only for intra-BSC handovers.
"msPwrOptLev(-110…-47,N) dbm
Minimum signal level measured by the MS when a handover is allowed to an adjacent cell. The signal level can be set independently for each adjacent cell.rxLevMinCell(-110…-47) dbm
The parameter indicates if the adjacent cell is synchronized with the cell in usesyncronised(Y/N)
The parameter defines the minimum signal level when a traffic reason handover is allowed to an adjacent cell.trhoTargetLevel(-110…-47,-110=N.map=X-110) dbm
OPTIONAL (C/I Based Handover Candidate Evaluation)The parameter indicates the difference between the signal level of the actual co-frequency cell of the handover candidate and the signal level of the reference cell which simulates the co-frequency celllevelAdjustment(-63…63) db
"OPTIONAL (C/I Based Handover Candidate Evaluation)The weighing coefficient of the reference cell.
The value 0 detaches the corresponding reference cell from the adjacent cell.
"ciEstWeight(0…10)
Direct Access to desired Layer/Band (S8)dadlbTargetCell(Y/N)
Dynamic Hotspot (S8),0=No Interference,1=Interference on regular frequencies,interferedCell(0…3)
The parameter defines the threshold value ofthe signal strength in the adjacent cell for the Directed Retry procedure. If the signal strength level in the cell is lower than this threshold value, the adjacent cell is not accepted as a candidate in directed retry.drThreshold
With this parameter you define whether the GPRS capability is enabled or disabled in the adjacent cell. In the adjacent cell creation if this parameter is not given and the SEG and the adjacent cell are in the same BSS, the value of this parameter is copied from the SEGgprsEnabled(Y/N)
"With this parameter you define the minimum power level an MS has to receive before it is allowed to access the adjacent cell.
"gprsRxLevAccessMin(-110…-47)dBm