【資料名稱】：TD-NODEB數據.txt

【資料作者】：無

【資料日期】：無

【資料語言】：中文

【資料格式】：TXT

【資料目錄和簡介】：


//選擇GPS做為時鐘源
ADD GPS: CN=0, SRN=0, SN=7, DELAY=0, TYPE=0, WORK_MODE=0, GN=0;
ADD CLKSRC: CLKSRC=GPS, PRI=1;
SET CLKMODE: MODE=AUTO;


//選擇NTP做為時間源，此處IP為RNC內網IP地址,需要根據現場實際情況修改
SET NTPC: IP="80.168.3.40", SYNCCYCLE=60, PORT=123, SYNCSWITCH=ON;
//選擇RNC做為時間源
SET TIMESRC: TIMESRC=NTP;

//MPT和風扇單板不用添加，PWR單板在使用環境告警的情況下才用添加。UTRP3支持IP和ATM傳輸，UTRP4僅支持IP傳輸
ADD BRD: CN=0, SRN=0, SN=S0, TYPE=BBP;
ADD BRD: CN=0, SRN=0, SN=S3, TYPE=BBI;

//由于三期發貨的NODEB MPT單板支持8E1

SET E1T1: CN=0, SRN=0, SN=7, SSN=0, PN=0, FRAME=E1_CRC4_MULTI_FRAME, LNCODE=HDB3, CLKM=SLAVE;
SET E1T1: CN=0, SRN=0, SN=7, SSN=0, PN=1, FRAME=E1_CRC4_MULTI_FRAME, LNCODE=HDB3, CLKM=SLAVE;
SET E1T1: CN=0, SRN=0, SN=7, SSN=0, PN=2, FRAME=E1_CRC4_MULTI_FRAME, LNCODE=HDB3, CLKM=SLAVE;
SET E1T1: CN=0, SRN=0, SN=7, SSN=0, PN=3, FRAME=E1_CRC4_MULTI_FRAME, LNCODE=HDB3, CLKM=SLAVE;
SET E1T1: CN=0, SRN=0, SN=7, SSN=0, PN=4, FRAME=E1_CRC4_MULTI_FRAME, LNCODE=HDB3, CLKM=SLAVE;
SET E1T1: CN=0, SRN=0, SN=7, SSN=0, PN=5, FRAME=E1_CRC4_MULTI_FRAME, LNCODE=HDB3, CLKM=SLAVE;
SET E1T1: CN=0, SRN=0, SN=7, SSN=0, PN=6, FRAME=E1_CRC4_MULTI_FRAME, LNCODE=HDB3, CLKM=SLAVE;
SET E1T1: CN=0, SRN=0, SN=7, SSN=0, PN=7, FRAME=E1_CRC4_MULTI_FRAME, LNCODE=HDB3, CLKM=SLAVE;


ADD IMAGRP: SN=7, IMAGRPN=0;
ADD IMALNK: SN=7, IMALNKN=0, IMAGRPN=0;
ADD IMALNK: SN=7, IMALNKN=1, IMAGRPN=0;
ADD IMALNK: SN=7, IMALNKN=2, IMAGRPN=0;
ADD IMALNK: SN=7, IMALNKN=3, IMAGRPN=0;
ADD IMALNK: SN=7, IMALNKN=4, IMAGRPN=0;
ADD IMALNK: SN=7, IMALNKN=5, IMAGRPN=0;
ADD IMALNK: SN=7, IMALNKN=6, IMAGRPN=0;
ADD IMALNK: SN=7, IMALNKN=7, IMAGRPN=0;



//添加一條NCP(承載在MPT上)、兩條CCP(承載在MPT上)、一條ALCAP(承載在MPT上)
ADD SAALLNK: SAALNO=0, SN=7, JNVCG=Not, PT=IMA, PN=0, VPI=1, VCI=40, ST=RTVBR, PCR=62, SCR=51;
ADD SAALLNK: SAALNO=1, SN=7, JNVCG=Not, PT=IMA, PN=0, VPI=1, VCI=41, ST=RTVBR, PCR=138, SCR=114;
ADD SAALLNK: SAALNO=2, SN=7, JNVCG=Not, PT=IMA, PN=0, VPI=1, VCI=42, ST=RTVBR, PCR=138, SCR=114;
ADD SAALLNK: SAALNO=13, SN=7, JNVCG=Not, PT=IMA, PN=0, VPI=1, VCI=53, ST=RTVBR, PCR=184, SCR=153;

ADD IUBCP: CPPT=NCP, BEAR=ATM, LN=0;
ADD IUBCP: CPPT=CCP, CPPN=0, BEAR=ATM, LN=1;
ADD IUBCP: CPPT=CCP, CPPN=1, BEAR=ATM, LN=2;

//注意：每塊接口板最多可以配置7條AAL2 Path。

ADD AAL2NODE: LN=13, ADDR="3900000000000000000000000000000000000000";
//PCR=1.86*1000*4-62-138-184=7056,SCR=PCR/1.1=7056/1.1=6414
ADD AAL2PATH: PATHID=1, SN=7, JNVCG=Not, PT=IMA, PN=0, VPI=1, VCI=54, ST=RTVBR, PCR=14496, SCR=13178, RCR=14496;
ADD AAL2PATH: PATHID=2, SN=7, JNVCG=Not, PT=IMA, PN=0, VPI=1, VCI=55, ST=NRTVBR, PCR=14496, SCR=13178, RCR=14496;
ADD AAL2PATH: PATHID=3, SN=7, JNVCG=Not, PT=IMA, PN=0, VPI=1, VCI=56, ST=RTVBR, PCR=14496, SCR=13178, RCR=14496;
ADD AAL2PATH: PATHID=4, SN=7, JNVCG=Not, PT=IMA, PN=0, VPI=1, VCI=57, ST=UBR, PCR=14496, RCR=14496;