告警歸屬告警代碼描述原因及影響
BSP[30] Clock A Signal LossBSP監察到TDMClock A Failure引起B(yǎng)SCOOS
BSP[31] Clock B Signal LossBSP監察到TDMClock B Failure引起B(yǎng)SCOOS
BSP[32] TDM Interface Failure分配時隙的記數器溢出引起TDM接口失敗，
BSP[34]TDM Interface Failure –TDM Parity ErrorTDM 奇偶錯誤
BSP[35]LAN Connection Failure主用的GPROC和備用的BSP 連接 Failure
BSP[39]Software Failure處理板軟件；處理板存在軟件或硬件故障
BSP[231]TDM Interface Configuration FailureTDM接口配置錯誤，引起B(yǎng)SPOSS
BSP[239] Process Safe Test Audit Failure處理板自檢失��；處理板存在軟件或硬件故障
BSP[254] Device Failure處理板故障；處理板存在軟件或硬件故障
CBUS[0]Over 50% OfBoards Detected Clock Failure系統總線故障；有可能會導致BSC/XCDR復位或者造成通訊故障
CBUS[2]Master CBUS Signal Provided By Slave GCLK系統總線故障；有可能會導致BSC/XCDR復位或者造成通訊故障
CBUS[4] Local KSWX/DSWX Clock Fibre Failure系統總線故障；有可能會導致BSC/XCDR復位或者造成通訊故障
GCLK[15] Watchdog Timer Expired同步硬件及MCU板故障引起
GCLK[16]Clock Output Failure在系統里GCLK的同步硬件沒有產生16.384MHz時鐘信號，導致時鐘輸出失敗
GCLK[17] SYNC Shutdown RequestGCLK 同步功能失敗
GCLK[18]Not OperationalMCU與GCLK同步功能失敗，無法操作
GCLK[19]Warmup FailureGCLK 啟動失敗
GCLK[20]Invalid ModeGCLK 硬件故障，引起GCLK 退服
GCLK[24]Bad Clock Source or OCXO (oscillator)…晶振振蕩器的故障；引起GCLK 退服
GCLK[232] Processor Bus Communication FailureGCLK 板的總線故障；引起GCLKOOS
GPROC[35] LAN Connection Failure主GPROC和備用GPROC在 LAN 連接失敗，可能導致GPROC 重起
GPROC[39]Software FailureGPROC處理板的軟件或硬件引起
GPROC[239]Process Safe test Audit Failure處理板自檢失敗，處理板存在軟件或硬件故障
GPROC[254] Device FailureGPROC管理系統的故障引起GPROC退服
GPRSGBL[0]Link DisconnectedBSS與SGSN失去通信
GPRS BSS[27]Last GBL Failed最后一條GBL退服，所有的GBL都OOS
GPRSPCU[ 0]Last GSL FailedPCU與BSC通信失敗，引起 PCUOOS
GPRSGSL[12]Link Traffic Too HighGSL 信令負荷超過警戎線，系統擁塞
GPRSGSL[10]Link DisconnectedPCU與BSC連接斷開
KSW[4] Clock A Signal Loss主時鐘信號丟失；可能引起B(yǎng)SSOOS
KSW[5] Clock B Signal Loss時鐘B信號丟失；可能引起B(yǎng)SSOOS
KSW[6]6.12 Second Reference Loss
KSW[7]Re-Initialized Unexpectedly KSW板RESET引起 KSW 重新初始化
KSW[8]Hard Reset硬件引起的復位
KSW[9]Watchdog timer ExpiredWatchdog 計數器過期引起KSW OOS
KSW[10]Lost Communication with KSW軟件處理器的錯誤導致和KSW板的通信失敗
KSW[11]Local Cage KSW TDM Loopback Test Failure本地KSW TDM循環測試失敗
KSW[18]--[21]Failure of Expanded Inbound TDM Highway
KSW[22]---[24]KSWX / DSWX in Slot 7-9 Detected Expanded KSW
KSW[25]---[27]KSWX/DSWX in Slot 21-23 Detected Expanded
KSW[224]Safe Test Audit FailureKSW 安全測試AUDIT 失敗
KSW[254]Device FailureKSW硬件設備失敗導致KSWOOS
KSW[232]Processor Bus Communication Failure處理器數據線通信失敗
LAN[0]Active & Standby LAN Failure主&備LANOOS
LAN[1] LAN FailureLAN 設備故障OOS
LANX25X25CircuitDown
MMSMMS[12]Bit Error Daily Threshold Exceeded比特誤碼率超出門限
MMSMMS[14]Bit Error OOS Threshold Exceeded比特誤碼率超出門限
MSIMSI [11]----MSI [40] DSP Channel (0–29) Audit FailureGDP audit 失敗引起單通
MTL[0]Signalling link failureMTL退服；影響B(tài)SC-MSC間信令傳輸
MTL[1]MSC Processor OutageMSC處理器引起的故障，MSC退服引起MTL鏈路BLOCK
MTL[3] Link Traffic Too High信令負荷超過門限；系統擁塞，影響GSM服務
MTLBSS0Last MTL link Failure –Signalling PointInaccessible最后一條MTL退服，引起B(yǎng)SS無法服務
PBUS[254]Device Failure系統總線故障；有可能會導致BSC/XCDR復位或者造成通訊故障
PCHCELL[24]PCH Queue Page Discard PCH_Q_PAGE_DISCARD 的統計超出范圍
PCHBSS[0]Paging Request From MSC Protocol ErrorPAGE_REQ_FROM_MSC_FAIl 的統計超出范圍
SBUS[254]Device Failure系統總線故障；有可能會導致BSC/XCDR復位或者造成通訊故障
SITE[0]Last RSL Link Failure基站最后1條RSL中斷；導致基站退服
SITE[5]Active Multiplexer 1 Loopback FailureMCUF/FMUX/FOX故障
TBUS[0]Remote KSW Loopback Test Failure系統總線故障；有可能會導致BSC/XCDR復位或者造成通訊故障
TBUS[3]Local KSWX/DSWX TDM Error系統總線故障；有可能會導致BSC/XCDR復位或者造成通訊故障
TBUS[4]Remote KSWX/DSWX TDM Error系統總線故障；有可能會導致BSC/XCDR復位或者造成通訊故障
XBL[10]Link DisconnectedXBL 鏈路中斷，BSC與RXCDR無法通信
XBL[12] Link Traffic Too HighXBL 信令負荷超過警戎線，系統擁塞
XBL[13]LAPD Protocol ErrorThresholdExceededLAPD協議超出單位時間內的次數