【資料名稱】：手機撥號上網錯誤代碼

【資料作者】：江展恒

【資料日期】：2012年07月6號

【資料語言】：中文

【資料格式】：DOC

【資料目錄和簡介】：

錯誤代碼錯誤原因中文譯文
600An operation is pending.一項未定的操作。
601The port handle is invalid.該端口控制器不可用。
602The port is already open.該端口已經打開。
603Caller's buffer is too small.呼叫緩沖器太小。
604Wrong information specified.錯誤的定義內容。
605Cannot set port information.不能設置端口內容。
606The port is not connected.該端口不能夠被連接。
607The event is invalid.該事件無效。
608The device does not exist.此類設備不存在。
609The device type does not exist.沒有該設備類型。
610The buffer is invalid.緩沖器不可用。
611The route is not available.不可用的路線。
612The route is not allocated.該路線不能夠被分配。
613Invalid compression specified.無效的壓縮說明。
614Out of buffers.緩沖器溢出。
615The port was not found.端口沒有找到。
616An asynchronous request is pending.未定的非同步請求。
617The port or device is already disconnecting.該端口或驅動器正在被斷開連接。
618The port is not open.該端口不能被打開。
619The port is disconnected.該端口不能被拆除。
620There are no endpoints.這沒有端點。
621Cannot open the phone book file.不能打開電話本。
622Cannot load the phone book file.不能裝入電話本。
623Cannot find the phone book entry.不能找到電話本入口。
624Cannot write the phone book file.不能寫入電話本。
625Invalid information found in the phone book.在電話本中存在不可用內容。
626Cannot load a string.不能裝入字符串。
627Cannot find key.沒有找到關鍵字。
628The port was disconnected.該端口不能被連接。
629The port was disconnected by the remote machine.該端口不能被遠程計算機連接。
630The port was disconnected due to hardware failure.該端口因?yàn)橛布�設備故障而不能被連接。
631The port was disconnected by the user.該端口不能被當前用戶連接。
632The structure size is incorrect.結構大小是正確的。
633The port is already in use or is not configured for Remote Access dial out.該端口已經被使用或不能被配置為遠程訪問使用。
634Cannot register your computer on the remote network.不能在遠程網絡上注冊你的計算機。
635Unknown error.未知錯誤。
636The wrong device is attached to the port.一個錯誤的設備被連接到該端口。
637The string could not be converted.該字符串不能夠被轉換。
638The request has timed out.請求超時。
639No asynchronous net available.沒有可用的異步通訊網絡。
640A NetBIOS error has occurred.產生一個NETBIOS錯誤。
641The server cannot allocate NetBIOS resources needed to support the client.該服務不能分配NETBIOS資源為用戶所使用。
642One of your NetBIOS names is already registered on the remote network.你的NETBIOS名字中的一個已經在遠程網絡中被注冊。
643A network adapter at the server failed.網卡的此項服務有問題。
644You will not receive network message popups.你不能收到POPUPS的網絡消息。
645Internal authentication error.內部鑒定錯誤。
646The account is not permitted to log on at this time of day.這個帳號在當天的這個時間不允許被登陸。
647The account is disabled.這個帳號已經被禁止。
648The password has expired.該密碼已經中止。
649The account does not have Remote Access permission.該帳號沒有遠程訪問權限。
650The Remote Access server is not responding.遠程訪問服務沒有被響應。
651Your modem (or other connecting device) has reported an error.你的MODEM或其他網路設備報告一個錯誤。
652Unrecognized response from the device.來自該設備未被認可得的響應。
653A macro required by the device was not found in the device .INF file section.該設備必須得宏在該設備的INF文件中沒有被找到。
654A command or response in the device .INF file section refers to an undefined macro。在該設備INF文件中的一條命令或響應提供了一個未定義的宏。
655The macro was not found in the device .INF file section.該“message”宏在該設備INF文件中不能被發現。
656The macro in the device .INF file section contains an undefined macro.該“defaultoff”宏在該設備INF文件中包含了一個未定義的宏。
657The device .INF file could not be opened.該設備的INF文件不能被打開。
658The device name in the device .INF or media .INI file is too long.在INF文件中設備名或在INI文件中的介質說明太長。
659The media .INI file refers to an unknown device name.該媒體的INI文件提供了一個未知的設備名。
660The device .INF file contains no responses for the command.該設備的INF文件包含對該命令不響應的內容。
661The device .INF file is missing a command.該設備的INF文件丟失一條命令。
662Attempted to set a macro not listed in device .INF file section.試圖設置的一個宏在設備的INF文件中沒有列出。
663The media .INI file refers to an unknown device type.媒體INI文件提供了一個未知的驅動器類型。
664Cannot allocate memory.無法分配內存。
665The port is not configured for Remote Access.該端口沒有給遠程訪問配置權限。
666Your modem (or other connecting device) is not functioning.你的MODEM或其他通訊設備當前是不活動的。
667Cannot read the media .INI file.無法讀取媒體INI文件。
668The connection dropped.掉線。
669The usage parameter in the media .INI file is invalid.在媒體INI文件中使用參數無效。
670Cannot read the section name from the media .INI file.無法從媒體INI文件中讀取段名。
671Cannot read the device type from the media .INI file.無法從媒體INI文件中讀取驅動器類型。
672Cannot read the device name from the media .INI file.無法從媒體INI文件中讀取驅動器名稱。
673Cannot read the usage from the media .INI file.無法從媒體INI文件中獲得用法。
674Cannot read the maximum connection BPS rate from the media .INI file.無法從媒體INI文件中讀取最大連接BPS速率。
675Cannot read the maximum carrier BPS rate from the media .INI file.無法從媒體INI文件中讀取最大載波BPS速率。
676The line is busy.線路忙。
677A person answered instead of a modem.人工應答替代MODEM。
678There is no answer.沒有應答。
679Cannot detect carrier.不能偵測到載波。
680There is no dial tone.沒有撥號音。
681General error reported by device.設備報告的一般性錯誤。
682ERROR WRITING SECTIONNAME寫段名錯誤。
683ERROR WRITING DEVICETYPE寫設備類型錯誤。
684ERROR WRITING DEVICENAME寫設備名錯誤。
685ERROR WRITING MAXCONNECTBPS寫最大連接BPS錯誤。
686ERROR WRITING MAXCARRIERBPS寫最大載波BPS錯誤。
687ERROR WRITING USAGE寫用法錯誤。
688ERROR WRITING DEFAULTOFF錯誤提示：寫默認設備。
689ERROR READING DEFAULTOFF錯誤提示：讀默認設備。
690ERROR EMPTY INI FILE錯誤提示：INI文件空。
691Access denied because username and/or password is invalid on the domain.訪問被拒絕是因?yàn)樵诒揪钟蚓W(wǎng)中用戶名或者密碼無效。
692Hardware failure in port or attached device.端口或者附屬設備的硬件有故障。
693ERROR NOT BINARY MACRO錯誤提示：沒有二進制的宏。
694ERROR DCB NOT FOUND錯誤提示：DCB沒有被發現。
695ERROR STATE MACHINES NOT STARTED錯誤提示：機器設備沒有被啟動。
696ERROR STATE MACHINES ALREADY STARTED錯誤提示：機器設備已經被啟動。
697ERROR PARTIAL RESPONSE LOOPING錯誤提示：部分循環響應錯誤。
698A response keyname in the device .INF file is not in the expected format.驅動器INI文件中的響應關鍵字不是標準的格式。
699The device response caused buffer overflow.驅動器響應導致緩沖器溢出。
700The expanded command in the device .INF file is too long.在驅動器的INI文件中的擴展命令太長。
701The device moved to a BPS rate not supported by the COM driver.驅動器改變的BPS速率不被COM口支持。
702Device response received when none expected.以外的收到設備響應。
703ERROR INTERACTIVE MODE錯誤提示：交互模式。
704ERROR BAD CALLBACK NUMBER錯誤提示：不可用的回叫號碼。
705ERROR INVALID AUTH STATE錯誤提示：無效的AUTH狀態。
706ERROR WRITING INITBPS錯誤提示: 初始化BPS錯誤。
707X.25 diagnostic indication.X—25診斷指示。
708The account has expired.該帳號已經被拒絕。
709Error changing password on domain.密碼改變錯誤。
710Serial overrun errors were detected while communicating with your modem.但使用你的MODEM通訊時，串行超限錯誤被偵測。
711RasMan initialization failure. Check the event log.RasMan 初始化失敗。請檢查事件記錄。
712Biplex port is initializing. Wait a few seconds and redial.Biplex 端口正在初始化。等一會兒再拔號。
713No active ISDN lines are available.非活動有ISDN線路可用。
714Not enough ISDN channels are available to make the call.半速動行的ISDN通道對電話呼叫來說是有效的。
715Too many errors occurred because of poor phone line quality.電話線路低略造成太多的錯誤。
716The Remote Access IP configuration is unusable.遠程訪問IP配置不可用。
717No IP addresses are available in the static pool of Remote Access IP addresses.對于靜態的遠程訪問IP地址庫來說沒有IP地址也是可用的。
718PPP timeout.PPP（Peer-Peer-Protocol）點對點協議通訊超時。
719PPP terminated by remote machine.PPP通訊被遠程設備終止。
720No PPP control protocols configured.沒有PPP控制協議被配置。
721Remote PPP peer is not responding.遠程PPP設備沒有應答。
722The PPP packet is invalid.該P(yáng)PP數據包是無效的。
723The phone number, including prefix and suffix, is too long.電話號碼（包括電話區號和分機號）太長。
724The IPX protocol cannot dial-out on the port because the computer is an IPX router.因?yàn)檫@臺計算機是IPX路由器，所以IPX協議在該端口不能被發送。
725The IPX protocol cannot dial-in on the port because the IPX router is not installed.因?yàn)镮PX路由器沒有安裝，所以IPX協議不能在該端口被接收。
726The IPX protocol cannot be used for dial-out on more than one port at a time.IPX協議在同一時間里只能由一個端口發送。
727Cannot access TCPCFG.DLL.不能打開TCPCFG.DLL文件。
728Cannot find an IP adapter bound to Remote Access.沒有找到用于遠程訪問的IP適配器。
729SLIP cannot be used unless the IP protocol is installed.除非IP協議被安裝，才能使用SLIP。
730Computer registration is not complete.計算機注冊沒有完成。
731The protocol is not configured.通訊協議沒有被配置。
732The PPP negotiation is not converging.PPP數據流不能被收集。
733The PPP control protocol for this network protocol is not available on the server.在該服務器上PPP控制協議對于整個網絡協議是不可用的。
734The PPP link control protocol terminated.PPP鏈接控制協議被終止。
735The requested address was rejected by the server.請求的地址被服務器彈出。
736The remote computer terminated the control protocol.遠程計算機終止了控制協議。
737Loopback detected.Loopback 被檢測。
738The server did not assign an address.該服務器沒有分配一個地址。
739The remote server cannot use the Windows NT encrypted password.遠程服務器不能使用WINNT 加密密碼。
740The TAPI devices configured for Remote Access failed to initialize or were not installed correctly.用于遠程訪問有TAPI設備初始化失敗或沒有被正確安裝。
741The local computer does not support encryption.本地計算機不支持加密。
742The remote server does not support encryption.遠程服務器不支持加密。
743The remote server requires encryption.遠程服務器需要加密。
744Cannot use the IPX net number assigned by the remote server. Check the event log.不能使用由遠程服務器分配的IPX網絡號。請檢查事件記錄。
752A syntax error was encountered while processing a script.當運行到該代碼時產生了一個語法錯誤。
753The connection could not be disconnected because it was created by the multi-protocol router.通訊不能被斷開，因?yàn)樵撏ㄓ嵄欢鄥f(xié)議路由器完成。
754The system could not find the multi-link bundle系統不能找到多功能鏈接包。
755The system cannot perform automated dial because this entry has a custom dialer specified.因?yàn)槎丝谝呀?jīng)被打開，所以系統不能自動完成拔號。
756This connection is already being dialed拔號連接正在進行。
757Remote access services could not be started automatically. Additional information is .....遠程訪問服務器不能自動啟動。增加信息是.......
758Internet connection sharing is already enabled on the connection.可以進行INTERNET共享連接。
760An error occurred while routing capabilities were being enabled.當路由容量正被打開時產生了一個錯誤。
761An error occurred while Internet connection sharing was being enabled for the connection.當共享INTERNET連接被打開時產生了一個錯誤。
763Internet connection sharing cannot be enabled. There are two or more LAN connections in .....共享INTERNET連接不能被打開。在....中有兩個或多個局域網連接在一起。
764No smart card reader is installed.沒有安裝智能卡讀卡器。
765Internet connection sharing cannot be enabled. A LAN connection is already configured .....INTERNET共享連接不能被打開。局域網連接被配置為.....
766The system could not find any certificate.系統不能找到任何加密算法。
767Internet connection sharing cannot be enabled. The LAN connection selected on the ......INTERNET共享連接不能被打開。局域網連接被設置在....
768The connection attempt failed because of failure to encrypt data.因?yàn)殄e(cuò)誤的加密數據造成連接請求失敗。
769The specified destination is not reachable.沒有找到目標設備。
770The remote machine rejected the connection attempt.遠程設備拒絕連接請求。
771The connection attempt failed because the network is busy.因?yàn)榫W(wǎng)絡忙造成連接請求失敗。
772The remote computer's network hardware is incompatible with the type of call requested.遠程計算機的網絡硬件與該類型的呼叫請求是不一致的。
773The connection attempt failed because the destination number has changed.因?yàn)槟繕?biāo)設備號碼被改變導致連接請求失敗。
774The connection attempt failed because of a temporary failure. Try connecting again.因?yàn)榕R時性錯誤導致連接請求失敗。請?jiān)僭囍�連接。
775The call was blocked by the remote computer.呼叫被遠程計算機阻止。
776The call could not be connected because the destination has invoked the Do Not Disturb feature.因?yàn)槟繕?biāo)設備已經調用Do Not Disturb feature，所以呼叫不能被連接。
777The connection attempt failed because the modem on the remote computer is out of order.因?yàn)檫h(yuǎn)程計算機中的MODEM超負荷工作，連接請求失敗。
778It was not possible to verify the identity of the server.校驗服務器的身份是不可能的。
779To dial out using this connection, you must use a smart card.你必須使用智能卡才能在該連接上發送。
780An attempted function is not valid for this connection對這次連接來說請求函數是無效的。
781The encryption attempt failed because no valid certificate was found.因?yàn)闆]有找到有效的加密算法造成加密請求失敗。